--- title: Adjusting printer margins description: Adjust the printer margins on the Sinfonia CS2 printer. --- [Skip to content](https://knowledge.hootboothphotobooth.com/adjusting-printer-margins#main-content) English Show submenu for translations ![HootBooth Photo Booth Logo](https://knowledge.hootboothphotobooth.com/hs-fs/hubfs/2017%20HootBooth%20Web%20Res%20Logo.png?width=125&height=105&name=2017%20HootBooth%20Web%20Res%20Logo.png) Open main navigation Close main navigation - English Show submenu for translations Browse our support resources - There are no suggestions because the search field is empty. 1. [HootBooth Photo Booth Knowledge base](https://knowledge.hootboothphotobooth.com/?hsLang=en) 2. [Onboarding Resources](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en) 3. [Sinfonia CS2 Printer](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#sinfonia-cs2-printer) # Adjusting printer margins ## How To: Adjusting Print Margins on the Sinfonia CS2 printer      You can adjust the position of prints by adjusting the margins. If you have "Automatically scale photo to fit paper" and/or "Center layout on paper" enabled, you can adjust print boundary that the layout is scaled and centered within.   #### 1. Print out a test print. Making sure to select a borderless paper size. Go to Settings > Printing and setup your printer, and then press the **Test** button. Note: Make sure "automatically rotate" is disabled for this test. #### 2. Look at the test print and check if the bounded area falls within the print area Looking at the test print and using the margin ruler... - The top edge seems fine - The left edge is to the left of the 10 mark (maybe 5) - The right edge is to the right of the 10 mark (maybe 5) - The bottom edge is above the 10 mark (maybe 13) #### 3. Set the margins based on the test print - Since the top edge is fine, leave it at zero - Use 5 for the left margin - Use 5 for the right margin - Use 13 for the bottom margin #### 4. Print out another test print with the margin settings Look for a bounding red box on the print which will defines the margin area. **If you do not see a side of the red box**, you will need increase the margin of that edge. **If the the side of the red box is too far from the edge of the paper**, you will need to decrease the margin of the edge. My print only show the bottom side of the red box. Do the left and right margins need to be increased by 1. The bottom side is a little too far from the bottom edge of the paper, so the bottom margin needs to be decreased by 1. Now to another test print with these margin settings. Now I can see the red box along the edge of the paper using the new margin settings. If you have "Center layout on paper" disabled, you will only be able to adjust the top and left margins. This will adjust the position of the top left corner of the image. - [Vendor Contact Phone Numbers & Links](https://knowledge.hootboothphotobooth.com/vendor-contact-phone-numbers-links?hsLang=en) - [Event Success](https://knowledge.hootboothphotobooth.com/event-success?hsLang=en) - [Onboarding Resources](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#main-content) - [Sparkbooth Software](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#sparkbooth-software) - [DSLR Software (PC ver)](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#dslr-software-pc-ver) - [Illumin8 Max setup](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#illumin8-max-setup) - [Sinfonia CS2 Printer](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#sinfonia-cs2-printer) - [Illumin8 kiosk](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#illumin8-kiosk) - [Curator Live software](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#curator-live-software) - [Illumin8 Air](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#illumin8-air) - [DSLR Hardware (setup)](https://knowledge.hootboothphotobooth.com/onboarding-resources?hsLang=en#dslr-hardware-setup) - [Troubleshooting](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#main-content) - [ILLUMIN8+ Photo Booth](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#illumin8-photo-booth) - [ILLUMIN8 MAX Photo Booth](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#illumin8-max-photo-booth) - [DSLR Camera settings](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#dslr-camera-settings) - [Parts](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#parts) - [Sparkbooth](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#sparkbooth) - [Printer](https://knowledge.hootboothphotobooth.com/troubleshooting?hsLang=en#printer) - [HootBooth by Booth.Events Software](https://knowledge.hootboothphotobooth.com/hootbooth-by-booth-events-software?hsLang=en) - [PBU Software - EventPRO DSLR Models](https://knowledge.hootboothphotobooth.com/pbu-software-eventpro-dslr-models?hsLang=en#main-content) - [HELP Articles](https://knowledge.hootboothphotobooth.com/pbu-software-eventpro-dslr-models?hsLang=en#help-articles) - [Setup Articles](https://knowledge.hootboothphotobooth.com/pbu-software-eventpro-dslr-models?hsLang=en#setup-articles) - [Software Platforms Terms of Service (TOS)](https://knowledge.hootboothphotobooth.com/software-platforms-terms-of-service-tos?hsLang=en#main-content) - [Curator iPad Photo Booth Software](https://knowledge.hootboothphotobooth.com/software-platforms-terms-of-service-tos?hsLang=en#curator-ipad-photo-booth-software) 1 [mailto:support@hootboothphotobooth.com](mailto:support@hootboothphotobooth.com) Copyright HootBooth Photo Booth© 2024,